How Does Carbon Capture Take CO2 Out of the Air? | How It Works

12 min read

On this page

What is the short answer?

Carbon capture catches carbon dioxide (CO2) before it escapes from a chimney, or pulls it out of open air, and then stores or uses it. Most plants pass a gas over a chemical that grabs CO2 and lets the other gases go.

Heating the chemical releases pure CO2 and readies the chemical for another round. The gas is then squeezed, moved by pipeline or ship, and pumped deep underground or used in products.

Definition: Carbon capture and storage (CCS) separates CO2 from a gas stream, compresses it, transports it and stores it deep underground. Direct air capture (DAC) takes CO2 from open air; combined with storage, it removes CO2 already in the atmosphere.

Where can CO2 be captured, and why does concentration matter?

The British Geological Survey (BGS) describes three ways to capture CO2 where fossil fuel is burned:

  • Post-combustion capture scrubs CO2 from the exhaust, or flue gas, and can be fitted to existing plants.
  • Pre-combustion capture first turns the fuel into a synthetic gas, then removes CO2 from that richer stream, which also yields hydrogen.
  • Oxy-fuel combustion burns fuel in oxygen, not air, so cooling the exhaust to remove water leaves almost pure CO2.

BGS adds gas processing, some industries and open air as sources.

Dilute gases are harder to separate and need more energy, the US National Academies of Sciences, Engineering, and Medicine explained in 2019. NOAA's preliminary global monthly mean for July 2026 was 426.10 parts per million (ppm). The Academies said CO2 in air is about 300 times more dilute than in coal power plant flue gas.

What chemistry grabs the CO2 and lets it go again?

CO2 acts as an acid, so capture chemicals are mostly bases. The National Academies name hydroxides and amines as among the simplest, used in solution or fixed to a solid.

  • Amine solvents. In the design Imperial College London describes, flue gas meets about 30% monoethanolamine (MEA) in water, which reacts with the CO2. In a stripper, heat reverses the reaction, giving pure CO2 and fresh solvent.
  • Liquid hydroxide DAC. Air meets potassium hydroxide solution: 2KOH + CO2 → H2O + K2CO3. Calcium hydroxide turns the carbonate into solid calcium carbonate and regenerates the KOH. A calciner heats the solid to about 900 °C: CaCO3 → CaO + CO2.
  • Solid sorbent DAC. Fans draw air over a solid carrying amine groups. Heat, sometimes with a vacuum, then releases the CO2: below 150 °C, say the Academies, or about 80 to 120 °C, says WRI, a think tank.

Why does capture take so much energy?

The bond that grabs CO2 must be broken again to free it and reuse the chemical, and that takes heat. Compression adds more. BGS says capturing and compressing CO2 raises a coal-fired power plant's fuel needs by 25 to 40%.

For air, the National Academies put the theoretical minimum at 0.45 gigajoules (GJ) per tonne of CO2. They put the real work of liquid hydroxide systems at 8.2 to 11 GJ, with reported calciner heat alone at 6 to 9 GJ.

WRI assumes about 2,000 kWh per tonne at scale. It warns that this energy must be very low carbon, or a plant could emit more CO2 than it captures.

What happens to the CO2 after capture?

Captured CO2 is compressed. Above about 31 °C and 74 bar, its critical point in NIST data, it becomes a dense supercritical fluid that BGS likens to a runny liquid. Pipelines are the cheapest transport, BGS says; ships can carry it as a liquid.

  • Geological storage. CO2 is injected into porous rock deep underground: old oil and gas fields, or saline formations, whose pores hold salty water. An impermeable caprock holds it down, and trapping processes slowly immobilise it, BGS explains.
  • Mineral storage. CO2 reacts with calcium, magnesium and iron in rock to form stable carbonate minerals, a natural process that is slow unless sped up, BGS notes.
  • Enhanced oil recovery (EOR). Injecting CO2 into old oil fields stores CO2 but also helps extract more oil. Carbon Brief, a climate news and analysis site, reported in August 2026 that around three-quarters of captured CO2 is used this way.
  • Products. Concrete can hold CO2 for centuries, but drinks and synthetic fuels release it quickly, WRI notes.

How is stored CO2 checked?

Monitoring starts before injection with a baseline survey of the rocks and surroundings, BGS explains. Repeat surveys then build time-lapse images of how the CO2 moves.

  • Deep monitoring, such as seismic surveys and sensors in wells, tracks CO2 in the reservoir and warns early if it rises.
  • Shallow monitoring checks soil, seabed, sea water and air for any CO2 that has escaped.

The US Environmental Protection Agency (EPA) regulates storage wells, called Class VI wells, to protect public health and underground drinking water. Monitoring continues until the permitting authority decides no more is needed. BGS reports the IPCC's view that well-selected, well-managed sites could retain over 99% of injected CO2 over 1,000 years.

Where is carbon capture running, and how much does it catch?

  • Norway. Equinor, the operator, says Sleipner has stored CO2 removed from its gas since 1996, over 19 million tonnes in the Utsira formation by the end of 2020. BGS gives a rate of about 1 million tonnes a year; Equinor's total works out at about 0.8 million a year. Under the government's Longship project, Gassnova, the state enterprise for CCS, lists a cement plant at Brevik built to capture 400,000 tonnes a year with amines. Northern Lights ships the liquid CO2 to Øygarden and pipes it to a reservoir 2,600 m below the North Sea seabed. Gassnova reported on 25 August 2025 that the first CO2 had been injected.
  • Iceland. Carbfix, begun in 2007, dissolves CO2 in water and pumps it into basalt at Hellisheiði, where it turns into carbonate rock within two years, the European Commission's Horizon magazine reported in September 2025.
  • Canada. Natural Resources Canada said in October 2014 that SaskPower's Boundary Dam project could capture up to one million tonnes a year. SaskPower, the operator, reports capturing 848,388 tonnes in 2024, its strongest year, and 721,239 tonnes in 2025.
  • United States. IRS instructions revised in December 2025 set the section 45Q tax credit, for facilities placed in service after 4 July 2025, at a base of $17 per metric ton, stored or used, and $36 for DAC with geological storage, before any inflation adjustment. Both are multiplied by 5 when wage and apprenticeship rules are met.

Worldwide, the IEA counted 75 operational CCS projects capturing 62.5 million tonnes a year as of February 2026, almost all at fossil fuel extraction and processing sites, Carbon Brief reported. The IEA's net-zero scenario has 1.7 billion tonnes captured by 2035, about 27 times as much.

What do supporters and critics argue?

  • Industry or fossil fuels? Supporters point to industry: the IPCC, an intergovernmental body, calls CCS a "critical mitigation option" for some sectors, including cement, and the IEA, an intergovernmental energy agency, calls it "virtually the only technology" that can significantly cut cement emissions, Carbon Brief reported in August 2026. Critics question its use on fossil fuels: Andrew Reid of IEEFA, a think tank, asked in Carbon Brief's Q&A if there is "really any point in trying to decarbonise fossil fuels", while saying it "may be a solution" for cement and chemicals. The IPCC noted in April 2022, Carbon Brief reported, that CCS, where available, "could allow fossil fuels to be used longer" and reduce the risk of stranded assets.
  • Cost. Supporters cite Jennifer Roberts, a University of Strathclyde researcher, who told Carbon Brief that in IPCC modelling, net zero without CCS "is far more expensive, disruptive and potentially out of reach". Critics cite a 2023 University of Oxford working paper estimating a "low-CCS" path at about $1 trillion a year cheaper than a "high-CCS" one, though it judged CCS "still likely necessary" for cement and chemicals.
  • Planned against achieved. IEEFA concluded in a 2023 analysis that most existing projects capture far less than the 90% or more of a source's CO2 widely aimed for, Carbon Brief reported. Proponents point to long-running projects, Carbon Brief notes; Sleipner has stored CO2 since 1996.
  • Removal or cuts? Supporters of removal cite the IPCC's April 2022 finding, reported by Carbon Brief, that removal to balance hard-to-abate residual emissions "is unavoidable" for net zero. WRI stresses cuts first, writing in September 2025 that cutting emissions "should always take priority" and that removal must not "take the place of rapid and deep emissions cuts".

How does this work with real numbers?

Both use NIST molar masses: carbon 12.0107 and CO2 44.0095 g/mol.

How much CO2 does one tonne of carbon make?

Each carbon atom gains two oxygen atoms, so 1 tonne of carbon, fully burned, becomes 44.0095 ÷ 12.0107 ≈ 3.66 tonnes of CO2. The rounded 44 ÷ 12 gives 3.67.

Going backwards: Boundary Dam's 721,239 tonnes of CO2 in 2025 held 721,239 × 12.0107 ÷ 44.0095 ≈ 197,000 tonnes of carbon.

Capture and storage handle the gas itself, so figures come in tonnes of CO2; the IRS counts only the CO2's weight, not water or impurities.

How much air holds one tonne of CO2?

Take NOAA's July 2026 figure of about 426 ppm and an illustrative 0 °C at 101.325 kPa, where NIST gives an ideal gas 22.414 litres per mole.

  • Air in 1 m³: 1,000 litres ÷ 22.414 ≈ 44.6 mol.
  • CO2 in 1 m³: 426 ppm by volume means 426 in every million molecules, so 44.6 × 0.000426 ≈ 0.0190 mol.
  • Mass: 0.0190 × 44.0095 ≈ 0.84 g of CO2 per cubic metre.
  • Air for 1 tonne: 1,000,000 g ÷ 0.84 g ≈ 1.2 million m³.

If a contactor catches 75% of the CO2, as in the National Academies' liquid design, about 1.6 million m³ must pass. On the Academies' 300 times figure, coal flue gas would hold a tonne in roughly 4,000 m³.

Where can the student go deeper in World 101?

This page follows CO2 from a chimney or open air into rock deep underground. The World 101 subject The Energy Transition looks at the wider change in how the world supplies and uses energy, away from fossil fuels and towards low-carbon electricity. Carbon capture is one much debated part of that wider change.

Three related subjects take these ideas further. Chemistry & the Molecular World explains the bonds and reactions behind amines, hydroxides and carbonates. Carbon Markets & Net Zero shows how prices on emissions and net zero goals shape what captured CO2 is worth. Adaptation & Geoengineering covers carbon dioxide removal, including direct air capture, alongside schemes to reflect sunlight.

Sources

  • NOAA Global Monitoring Laboratory, global monthly mean CO2 (July 2026), updated 9 October 2026.
  • British Geological Survey, "Understanding carbon capture and storage"; Imperial College London, solvent capture page; both read 9 November 2026.
  • National Academies of Sciences, Engineering, and Medicine, Negative Emissions Technologies and Reliable Sequestration, chapter 5, 2019.
  • World Resources Institute, "Direct Air Capture: 6 Things To Know", 2 September 2025.
  • NIST Chemistry WebBook and CODATA 2022 molar volume; Equinor, Sleipner page (since 1996; stored by end of 2020); both read 9 November 2026.
  • Gassnova, Brevik page, read 9 November 2026, and news, 25 August 2025; Northern Lights, "What we do", read 9 November 2026.
  • European Commission, Horizon magazine, 2 September 2025 (Carbfix since 2007).
  • Natural Resources Canada, news release, 2 October 2014; SaskPower, status updates, 21 January 2025 (2024 data) and 27 January 2026.
  • US Internal Revenue Service, Form 8933 instructions, revised December 2025; US EPA, Class VI wells page, updated 18 August 2026.
  • Carbon Brief: CCS Q&A, 3 August 2026 (IEA data to February 2026 and scenario to 2035; IEEFA 2023 analysis; Oxford 2023 working paper); Q&A on the IPCC Sixth Assessment Report, Working Group III, 5 April 2022.

Common errors and misconceptions

  • Misconception: All carbon capture removes CO2 from the atmosphere. Correct: Capture at a fossil fuel chimney stops new CO2 escaping; direct air capture with storage takes out CO2 already in the air.
  • Misconception: Stored CO2 sits underground as a loose gas bubble. Correct: It goes into porous rock as a dense supercritical fluid, under a caprock, where trapping processes immobilise it.
  • Misconception: A capture plant catches all of a source's CO2. Correct: IEEFA found most projects far below 90%; Boundary Dam's best year was 848,388 tonnes against up to one million stated.
  • Misconception: Capturing CO2 from air is as easy as from a chimney. Correct: Air is about 300 times more dilute than coal flue gas, so far more gas must be handled.
  • Misconception: Burning one tonne of carbon makes one tonne of CO2. Correct: Each carbon atom gains two oxygen atoms, so it makes about 3.66 tonnes.

Key takeaways

  • Capture uses bases such as amines or hydroxides, which bind CO2 from flue gas or air and release it when heated.
  • Freeing the CO2 and reusing the chemical takes heat, so capture costs much energy, more still for dilute air.
  • Captured CO2 is compressed, piped or shipped, and stored in saline formations, old oil and gas fields or basalt, or used.
  • Storage sites are checked against a baseline with time-lapse surveys, under rules from regulators such as the US EPA.
  • Norway, Iceland, Canada and the United States show gas processing, cement capture, mineral storage, a coal plant and a per-tonne tax credit.
  • The IPCC, the IEA, IEEFA, WRI and Oxford researchers are among those cited on capture's place, cost and record.

Test yourself

Why is an amine solvent heated in a stripper?

Heat reverses the reaction between the amine and CO2, releasing pure CO2 and regenerating the solvent for reuse.

How does oxy-fuel combustion make CO2 easier to capture?

Burning fuel in oxygen leaves mostly CO2 and water vapour; removing the water leaves almost pure CO2.

How much CO2 comes from burning 2 tonnes of carbon completely?

2 × 44.0095 ÷ 12.0107 ≈ 7.33 tonnes of CO2.

Why must a direct air capture plant move so much air?

At 426 ppm and 0 °C, each cubic metre holds only about 0.84 g of CO2, so a tonne needs roughly 1.2 million m³.

What happens to CO2 in Iceland's Carbfix method?

It is dissolved in water and pumped into basalt, where it turns into carbonate minerals within about two years.

Why is a storage site surveyed before injection begins?

It records the starting state, so later time-lapse surveys show how the CO2 moves and whether any escapes.

Go deeper in World 101: The Energy Transition

Write about it

Turn a question from this chapter into a paper.

The Writing Studio has a structure guide, a rubric and citation tools for 15 formats, from essays to research papers. A free account keeps up to five drafts. Learnacy Essential adds feedback from an AI writing coach and submission to The OYI Review.

Publication depends on review and is not guaranteed.